Pontoon Bimini Top Sirius 9 9' long custom width for perfect fit 1.25

This is the BEST pontoon bimini top available. 9.25oz marine grade Sunbrella. This thread won't break... 4 bow 1.25 Square tube frame. Stainless Steel Eye Ends, Front Braces, Rear Braces with Trailering Brace.

The trailering brace allows your bimini to sit up a few inches off the deck of your boat for transport on the road. The trailer brace uses the same deck mounts as the rear brace. You tell us how wide your boat is at the mounting point and we will build this frame and bimini top to within 1 of your dimension.

These are truly custom bimini tops. Accon Marine Quick Release Deck Mounts. These are a must if you have furniture on your pontoon that rises above the top rail of your boat. Typically pull pins are used to connect the frame to the deck moun.

Those pull pins can push into the back of your seats leaving a mark or even worse - damaging your seat backs. These utilize a different means of securing the bimini to your deck mounts - stainless eye ends in the bottom of the frame and braces that fall into a slot on the accon deck mount. Easy on, easy off and not pull pins to hit the back of your seats. Most boots are put together with one seam that travels the length of the entire boot. We use two seams that travel the length of the boot.

What that does is allows the boot to form fit the corners of the frame. We also use a velcro flap to allow the boot to go on around the stern light instead of dropping the boot down over the top of the stern light. Much easier and quicker to take on and off. Color coordinated binding/edging goes not only all the way around the outside of your bimini top, but also on the 4 zippered pockets that are used to attach this bimini to the frame.

We also put a snap in each corner to ensure it is centered on the frame and won't move around while underway. We also run all of our sunbrella parts through a surging machine that locks in the edge to prevent unravelling. We then put the binding/edging over that. All of the hardware we provide for this bimini top is included.

We use heavy duty stainless bolts, washers and locknuts to secure this to your boat. We also provide a wire for the stern light and of course all installation instructions. The ideas we put into this bimini are come directly from our customers and our own market research. We are confident in saying it is the best top available anywhere.

We have been making bimini tops and other items for the marine industry for over 35 years. We have the experience in this market and anxious to share it with you. Chances are if it doesn't look very good in a picture it is not going to look very good on your boat. The right bimini top will set your boat off right no matter how old or new your boat is. We design these frames and bimini tops to stand up to high speeds on the water given how fast pontoon boats are running now! The frame will sit back on its rear braces or lay flat on your rails. We manufacture these tops right here in the USA!

I realize it can become overwhelming. We want to provide you with the exact kind of bimini top you require. Just know that all of our bimini tops come with the following options.

1 frame with standard black vinyl fittings and deck mounts. 1 frame with metal fittings and deck mounts. 1.25 frame with metal fittings and deck mounts. We can customize the width from 6' wide to 8'6 wide at no additional cost. We offer three fabrics with three different warranties - 10 year, 5 year, and 3 year.

Your satisfaction is our goal! The item "Pontoon Bimini Top Sirius 9 9' long custom width for perfect fit 1.25" is in sale since Tuesday, December 10, 2013. This item is in the category "eBay Motors\Parts & Accessories\Boat Parts\Accessories & Gear\Covers".

The seller is "canvasguy2077" and is located in Toledo, Ohio. This item can be shipped worldwide.

Brand: northstar
Manufacturer Part Number: sirius9
Country/Region of Manufacture: United States
Country of Manufacture: United States